Leading and lagging current

src: slideplayer.com

Leading and lagging current are phenomena that occur as a result of alternating current. In a circuit with alternating current, the value of voltage and current vary sinusoidally. In these types of circuits, the terms lead, lag, or in phase are used to describe current with reference to voltage. Current is in phase with voltage when there is no phase shift between the sinusoids describing their time varying behavior. This generally occurs when the load drawing the current is resistive.

In electric power flow, it is important to know whether current is leading or lagging because it can be used to describe how much circulating reactive power flow is occurring in the system, and whether that power is inductive or capacitative. It can also play an important role in the operation of three-phase power systems.

Video Leading and lagging current

Angle notation

Angle notation can easily describe leading and lagging current:

 ${\displaystyle A\angle \theta .}$

In this equation, the value of theta is the important factor for leading and lagging current. As mentioned in the introduction above, leading or lagging current represents a time shift between the current and voltage sine curves, which is represented by the angle by which the curve is ahead or behind of where it would be initially. For example, if ? is zero, the curve will have amplitude zero at time zero. Using complex numbers is a way to simplify analyzing certain components in RLC circuits. For example, it is very easy to convert these between polar and rectangular coordinates. Starting from the polar notation,  ${\displaystyle \angle \theta }$ can represent either the vector  ${\displaystyle (\cos \theta ,\sin \theta )\,}$  or the rectangular notation  ${\displaystyle \cos \theta +j\sin \theta =e^{j\theta },\,}$  both of which have magnitudes of 1.

Maps Leading and lagging current

Lagging current

 ${\displaystyle A\angle \theta =A\angle \delta -\beta }$

Lagging current can be formally defined as "an alternating current that reaches its maximum value up to 90 degrees behind the voltage that produces it." This means that current lags the voltage when ${\displaystyle \beta }$, the angle of the current sine wave with respect to an arbitrarily chosen reference, is less than ${\displaystyle \delta }$, the angle of the voltage sine wave with respect to the same reference. Therefore, current can quickly be identified as lagging if the angle ${\displaystyle \theta }$ is positive. For example, if the voltage angle ${\displaystyle \delta }$ is zero, current will be lagging if ${\displaystyle \beta }$ is positive. This is often the case because voltage is taken as the reference.

In circuits with primarily inductive loads, current lags the voltage. This happens because in an inductive load, it is the induced electromotive force that causes the current to flow. Note that in the definition above, the current is produced by the voltage. The induced electromotive force is caused by a change in the magnetic flux linking the coils of an inductor.

src: i.ytimg.com

Leading current

 ${\displaystyle A\angle \theta =A\angle \delta +\beta }$

Leading current can be formally defined as "an alternating current that reaches its maximum value up to 90 degrees ahead of the voltage that it produces." This means that the current leads the voltage when ${\displaystyle \beta }$, the angle of the current sine wave with respect to an arbitrarily chosen reference is greater than ${\displaystyle \delta }$, the angle of the voltage sine wave with respect to the same reference. Therefore, current can quickly be identified as leading if the angle ${\displaystyle \theta }$ is negative. For example, if the voltage angle ${\displaystyle \delta }$ is zero, current will be leading if ${\displaystyle \beta }$ is negative. This is often the case because voltage is taken as the reference.

In circuits with primarily capacitive loads, current leads the voltage. This is true because current must first flow to the two plates of the capacitor, where charge is stored. Only after charge accumulates at the plates of a capacitor is a voltage difference established. The behavior of the voltage is thus dependent on the behavior current and on how much charge accumulates. This is why the formal definition states that the current produces the voltage.

src: indexxit.com

Visualizing leading and lagging current

A simple phasor diagram with a two dimensional Cartesian coordinate system and phasors can be used to visualize leading and lagging current at a fixed moment in time. In the real-complex coordinate system, one period of a sine wave corresponds to a full circle in the complex plane. Since the voltage and current have the same frequency, at any moment in time those quantities can be easily represented by stationary points on the circle, while the arrows from the center of circle to those points are called phasors. Since the relative time difference between functions is constant, they also have a constant angle difference between them, represented by the angle between points on the circle.

src: i.stack.imgur.com

Historical documents regarding leading and lagging currents

An early source of data is an article from the 1911 American Academy of Arts and Sciences by A.E. Kennelly. Kennelly uses traditional methods in solving vector diagrams for oscillating circuits, which can also include alternating current circuits as well.

src: i.ytimg.com

See also

• Electrical impedance
• Power factor
• Volt-ampere
• Volt-ampere reactive

src: indexxit.com

Notes

References:

src: i.ytimg.com

References

• Bowick, Chris, John Blyler, and Cheryl J. Ajluni. RF Circuit Design. 2nd ed. Amsterdam: Newnes/Elsevier, 2008. Print.
• Gaydecki, Patrick. Foundations of Digital Signal Processing: Theory, Algorithms and Hardware Design. 2nd ed. London: Institution of Electrical Engineers, 2004. Print
• Gilmore, Rowan, and Les Besser. Passive Circuits and Systems. Boston [u.a.: Artech House, 2003. Print.
• Hayt, W. H., and J. E. Kemmerly. Engineering Circuit Analysis. 2nd ed. New York: McGraw-Hill, 1971. Print.
• Kennelly, A. E. "Vector-Diagrams of Oscillating-Current Circuits." American Academy of Arts & Sciences 46.17 (1911): 373-421. Jstor. ITHAKA. Web. 1 May 2012. <https://www.jstor.org/stable/20022665>.
• "Lagging Current." TheFreeDictionary.com. Web. 1 May 2012. (http://encyclopedia2.thefreedictionary.com/lagging_current)
• "Leading Current." TheFreeDictionary.com. Web. 1 May 2012. (http://encyclopedia2.thefreedictionary.com/leading_current)
• Nilsson, James William; Riedel, Susan A. (2008). Electric circuits (8th ed.). Prentice Hall. p. 338. ISBN 0-13-198925-1, Chapter 9, page 338
• Smith, Ralph J. Circuit Devices and Systems. 3rd ed. New York: John Wiley & Sons, 1976. Print.
• Glover, Duncan J. Power System Analysis and Design. 5th ed. Cengage Learning, 2014.
• Masters, G. Renewable and Efficient Electric Power Systems. 2nd ed. Wiley, 2004.

Source of the article : Wikipedia